Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
indigo_2025.2_documentation:device_class [2026/05/04 11:05] – [Decrease Cool Setpoint] davel17indigo_2025.2_documentation:device_class [2026/05/04 11:09] (current) – [Set Heat Setpoint] davel17
Line 1503: Line 1503:
 ^  Parameters  ^^^^ ^  Parameters  ^^^^
 ^  Parameter  ^  Required  ^  Type  ^  Description  ^ ^  Parameter  ^  Required  ^  Type  ^  Description  ^
-|direct parameter|  Yes  |  integer  |id or instance of the device|+|direct parameter|  Yes  |  float  |id or instance of the device|
 |''//delta//''|  No  |  float  |Number of degrees to decrease the heat setpoint.  If unspecified, the change will be equal to one degree.| |''//delta//''|  No  |  float  |Number of degrees to decrease the heat setpoint.  If unspecified, the change will be equal to one degree.|
  
Line 1515: Line 1515:
 ^  Parameters  ^^^^ ^  Parameters  ^^^^
 ^  Parameter  ^  Required  ^  Type  ^  Description  ^ ^  Parameter  ^  Required  ^  Type  ^  Description  ^
-|direct parameter|  Yes  |  integer  |id or instance of the device|+|direct parameter|  Yes  |  float  |id or instance of the device|
 |''//delta//''|  No  |  float  |Number of degrees to increase the cool setpoint.  If unspecified, the change will be equal to one degree.| |''//delta//''|  No  |  float  |Number of degrees to increase the cool setpoint.  If unspecified, the change will be equal to one degree.|
  
Line 1527: Line 1527:
 ^  Parameters  ^^^^ ^  Parameters  ^^^^
 ^  Parameter  ^  Required  ^  Type  ^  Description  ^ ^  Parameter  ^  Required  ^  Type  ^  Description  ^
-|direct parameter|  Yes  |  integer  |id or instance of the device|+|direct parameter|  Yes  |  float  |id or instance of the device|
 |''//delta//''|  No  |  float  |Number of degrees to increase the heat setpoint. If unspecified, the change will be equal to one degree.| |''//delta//''|  No  |  float  |Number of degrees to increase the heat setpoint. If unspecified, the change will be equal to one degree.|
  
Line 1539: Line 1539:
 ^  Parameter  ^  Required  ^  Type  ^  Description  ^ ^  Parameter  ^  Required  ^  Type  ^  Description  ^
 |direct parameter|  Yes  |  integer  |id or instance of the device| |direct parameter|  Yes  |  integer  |id or instance of the device|
-|''//value//''|  Yes  |  integer  |the absolute temperature of the setpoint|+|''//value//''|  Yes  |  float  |the absolute temperature of the setpoint|
  
 === Set Fan Mode === === Set Fan Mode ===
Line 1561: Line 1561:
 ^  Parameter  ^  Required  ^  Type  ^  Description  ^ ^  Parameter  ^  Required  ^  Type  ^  Description  ^
 |direct parameter|  Yes  |  integer  |id or instance of the device| |direct parameter|  Yes  |  integer  |id or instance of the device|
-|''//value//''|  Yes  |  integer  |the absolute temperature of the setpoint|+|''//value//''|  Yes  |  float  |the absolute temperature of the setpoint|
  
 === Set HVAC Mode === === Set HVAC Mode ===
  • /www/perceptive/wiki/data/attic/indigo_2025.2_documentation/device_class.1777892720.txt.gz
  • Last modified: 2026/05/04 11:05
  • by davel17